Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +1 248 650 0500
- +1 248 650 0501
- sales@elcometer.com
- 6900 MIller Drive
Warren, Michigan 48092
United States of America
-
Product
Setaflash 'Series 3' Active-Cool Closed Cup Tester
6910/3
-
The Elcometer 6910/3 Setaflash ‘Series 3’ Active-Cool Closed Cup Tester offers the same features as the Elcometer 6910/1 Setaflash but is fitted with a cup suitable for testing corrosive samples.
-
Product
Calibration
-
Formal quality systems, such as those described in ISO 9000, require gauges to be properly controlled, logged and in calibration. Increasingly, users are specifying that the readings taken by gauges are traceable to National Standards. There are three types of coating thickness standards available from Elcometer: calibration foils, coated standards and zero test plates.
-
Product
Buchholz Hardness Tester
3095
-
Measuring a coating’s hardness using the indentation method, the Elcometer 3095 Buchholz Hardness Tester consists of a bevelled disc indenting tool that is fitted into a stainless steel block exerting a constant test load of 500g (17.6oz).
-
Product
Surface Roughness
-
Surface Roughness: these consist of a stylus attached to an arm which moves over the surface to record and measure the roughness over a specified distance, recording peak-to-valley average.
-
Product
Pfund Thickness Gauge
3233
-
Available in aluminium or stainless steel this instrument consists of two concentric cylinders, one sliding inside the other. A spherical glass lens, which has engraved measurements, is fitted to the end of the central cylinder and when pressed into the wet film, leaves a circular trace.The diameter of the mark on the lens is measured and, using the supplied conversion table, the thickness of the coating can be easily assessed.Ideal for measuring the thickness of wet translucent products such as varnishes, oils etc.Measurement range of 2.25 - 360μm (0.09 - 14.17mils)
-
Product
Duct Deposit Measuring System
-
The Elcometer 456 Duct Deposit Measuring System has been specifically designed to meet the requirements of the DTT (Deposit Thickness Test) in HVCA’s (Heating & Ventilation Contractor’s Association) Guide to Good Practice, for the measurement of dust and grease deposits within ventilation systems and kitchen ducts made of ferrous metals.
-
Product
Hygrometer
308
-
The Elcometer 308 Hygrometer has been specifically designed for use in very hot climates where the surface temperature of the substrate can exceed the paint manufacturer’s recommended limits for successful painting.Painting outside recommended limits can have a detrimental affect on the performance and lifetime of the coating.Key features of the Elcometer 308 Hygrometer include:Rugged design: Suitable for use in extreme environments the Elcometer 308 Hygrometer is dustproof and waterproof with fully sealed sensors.Measurement Hold / Release function: With a single button press readings are ‘held’ on the screen. These can then be recorded before simply pressing the button again to ‘release’ the screen and continue to take further readings as necessary.Backlight: Bright screen making information easy to read – ideal in dark or confined spaces.
-
Product
Chloride Ion Test Kit for Water
134W
-
The Elcometer 134W is used to monitor recycled water (after it has been applied) to establish effectiveness of salt removal, this test is ideal for testing the salt contamination in wash water and blast water.
-
Product
Manual Clemen Unit
Elcometer 3000
-
The Elcometer 3000 Manual Clemen Unit is a robust and simple to use instrument for evaluating the resistance to scratching of a coated surface.
-
Product
Automatic Pull-Off Adhesion Gauge
510
-
Automatic hydraulic pump ensures smooth and continuous pressure application for consistent, repeatable adhesion strength resultsFully adjustable pull rates 0.1-1.4MPa/s (14.5-203psi) to meet National and International StandardsCan be used with 10,14.2, 20 and 50mm diameter dolliesUser definable limits with unique pressure hold and release functionUser definable measurement range with an accuracy of ±1% of full scale:10mm dolly: 100MPa (14400psi14.2mm dolly: 50MPa (7200psi)20mm dolly: 25 MPa (3600psi)50mm dolly: 4MPa (580psi)Dust and water resistant rugged design to IP64Interchangeable units: MPa, psi, Nmm2 and NA range of standard and thin substrate actuator skirts (compatible with Elcometer 506) available for adhesive strength testing on thick, thin, flat or convex substratesStore up to 60,000 readings with individual pull graphs in up to 2,500 alpha numerical batches, complete with attribute failure informationUSB and Bluetooth® data output - compatible with ElcoMaster® App for iPhone, iPod, iPad and Android mobile devices
-
Product
Surface Profile Gauge
123
-
The Elcometer 123 Surface Profile Gauge is an easy to use analogue gauge which measures the peak-to-valley height of a blast cleaned surface in a similar way to the Elcometer 224 Digital Surface Profile Gauge.
-
Product
Washability & Abrasion
-
Improved mechanical resistance to wear is a key requirement of a wide range of products. From coatings to clothing, leather to upholstery, keypads to plastic toys, a product’s ability to resist wear is an important characteristic. There are testing methods relating to the ‘abrasion by friction’ concept. Others are based on the projection of abrasive particles on to the test specimen. These techniques provide valuable information about materials and processes.
-
Product
Covermeter
331B
-
The easy to use Elcometer 331B Covermeter quickly and accurately locates/orientates reinforcement bars in concrete and measures the depth of cover over the rebar.
-
Product
Mechanical Coating Thickness Gauges
-
Mechanical Coating Thickness Gauges are suitable for working in high risk areas such as high temperature or flammable atmospheres, underwater or where the risk of explosion is high and could be triggered by the use of an electronic instrument. From the simplest coating thickness gauge Elcometer 101 which will provide you with quick and immediate results to the more accurate coating thickness gauge Elcometer 211, also called the "banana gauge" which is ideal for cold and underwater surfaces.
-
Product
Scratch/Shear Tester
3025
-
The Elcometer 3025 Scratch/Shear Tester is used to test the resistance of many materials to scratching, shearing, gouging, marring, scraping and engraving.
