Pulse Instruments
Pulse Instruments is a leading manufacturer of systems and equipment for characterization and production test of CMOS, CCD and IR image sensors, including science-grade devices. Science teams have used Pulse Instruments systems to extract maximum performance from several HST CCDs, including the chip in the most recently installed Advanced Camera System that is providing 10x the performance of its predecessor.
- (310) 515-5330
- sales@pulseinstruments.com
- 22301 S. Western Ave.
#107,
Torrance, CA 90501
United States of America
-
Product
CMOS/CCD Production Test System
System 1828
-
The basic system consists of a 225 MHz pattern generator, 10 clock drivers, 6 DC biases, 1-4 channels of 10 MHz 14 bit analog data acquisition and/or 1-4 channels of digital acquisition. Additional options can be added to customize the system to meet your requirements.
-
Product
Clock Drivers
-
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
Product
Four Channel Clock Driver Card
PI-41401
-
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-
Product
Instrument Mainframe
PI-11008
-
The PI-11008 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
Product
SystemSolutions
-
Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your yourdevice, not on your test system.
-
Product
Pulse Instruments Data Acquisition and Test Software
PI-DATS
-
PI-DATS is Pulse Instruments Data Acquisition and Test Software, our user-friendly system software that allows complete control over Pulse Instruments test systems and test equipment. PI-DATS can dramatically increase your testing productivity by decreasing the amount of time it takes to set up and change test plans.
-
Product
Mainframes
-
Our CompactPCI series mainframes are industry-standard, open-architecture chassis with enhancements to support Pulse Instruments' clock driver and DC bias cards. The enhancements are transparent to the CompactPCI specification, and 3rd-party cards CompactPCI/PXI cards can be used in our mainframes without hardware or software modification*.
-
Product
Low-Noise DC Bias
-
Imaging devices, such as CCDs, IR FPAs, and CMOS image sensors, require DC bias with very low electrical noise to prevent contamination of the image. Image quality can also be enhanced by carefully tuning each bias voltage to extract the maximum signal/noise ratio out of an array. Pulse Instruments has decades of experience providing DC bias supplies with the flexibility required tocharacterize and test a variety of devices while maintaining the noise immunity required for satellite and astronomy applications.
-
Product
Characterization System
System 7700
-
Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your your device, not on your test system.
-
Product
Graphical Waveform Editor and Instrument
PI-PAT
-
Much more than just a visualization tool, PI-PAT is a full-fledged graphical waveform editor that allows you to spend more time testing and less time programming. PI-PAT doesn't require any programming experience or complicated syntax. Just draw or type patterns directly into the pattern window. Move a clock edge by dragging it. Adjust integration times by entering a single number. Change the output to your DUT by clicking the Update button. You'll never have to wrangle DSP or FPGA code with PI-PAT.
